When you want to show off your lawn, there is nothing nicer than having clear cut areas that define the separation between turf and flowerbeds or other formations. There are many towns and neighborhood associations that reward those that spend the time it takes to create a beautiful looking lawn. With a plastic bender board, you can create that clean separation with ease and keep the weeds from encroaching on your beds.
Two different types exist and are in use today. The first is made from packed wood fibers and other natural materials. Though it is a great way to create the border, it will have to be replaced over time because it is designed to decay and work its way into the soil. The plastic type will not decay over time and is environmentally sound because it is made of recycled plastics that would be headed to the landfill. It will last much longer and keep doing its job for years.
First, figure out how much you need. The easiest procedure is to put a few stakes in the ground along the path you will take. Run a length of string between the stakes and then measure the string. This way you won't have to use an inflexible measuring tape along the bending path and take your best guess. If you want to be sure, add a few inches to the measurement since you can cut off what you don't need.
When you are done measuring and getting the material, it is time to dig. The hole should be about six inches wide and deep enough for the whole board to sit below the surface. Don't dispose of the dirt because you are going to need it at the end to fill the hole back in.
After digging, start putting in the stakes. You should have several to help hold the board in place. As you hammer them in with your rubber mallet, make sure they are placed so the material will sit on the turf side of the stakes. This will keep the grass from growing where it shouldn't.
The fourth step is to cut the material to length and place in the ground. It is easier if you roll the material out next to the trench. When done, make your cuts and slide the border into the hole and secure it to the stakes. This keeps it in place. If you notice any areas that are riding too high and will be exposed, just use a trowel and dig the dirt out from under it and place it to the side.
Use the dirt to fill the trench. Using a rake or shovel, fill in the trench until the dirt is all used up. There should be quite a bit left over and a nice mound will be on top. This fine since the dirt will settle in a few days. Pack it in by stomping on it or using a stamp or rake. After a few days of settling, you can begin to place stones on top if you want to create a nice visible border.
Now you are done. You have successfully placed a border between your grass and other landscaping. This will help keep the weeds out and let you avoid mowing up into the flowerbeds. The border will help prevent weeds and provide the needed separation between the beds and the grass.
Two different types exist and are in use today. The first is made from packed wood fibers and other natural materials. Though it is a great way to create the border, it will have to be replaced over time because it is designed to decay and work its way into the soil. The plastic type will not decay over time and is environmentally sound because it is made of recycled plastics that would be headed to the landfill. It will last much longer and keep doing its job for years.
First, figure out how much you need. The easiest procedure is to put a few stakes in the ground along the path you will take. Run a length of string between the stakes and then measure the string. This way you won't have to use an inflexible measuring tape along the bending path and take your best guess. If you want to be sure, add a few inches to the measurement since you can cut off what you don't need.
When you are done measuring and getting the material, it is time to dig. The hole should be about six inches wide and deep enough for the whole board to sit below the surface. Don't dispose of the dirt because you are going to need it at the end to fill the hole back in.
After digging, start putting in the stakes. You should have several to help hold the board in place. As you hammer them in with your rubber mallet, make sure they are placed so the material will sit on the turf side of the stakes. This will keep the grass from growing where it shouldn't.
The fourth step is to cut the material to length and place in the ground. It is easier if you roll the material out next to the trench. When done, make your cuts and slide the border into the hole and secure it to the stakes. This keeps it in place. If you notice any areas that are riding too high and will be exposed, just use a trowel and dig the dirt out from under it and place it to the side.
Use the dirt to fill the trench. Using a rake or shovel, fill in the trench until the dirt is all used up. There should be quite a bit left over and a nice mound will be on top. This fine since the dirt will settle in a few days. Pack it in by stomping on it or using a stamp or rake. After a few days of settling, you can begin to place stones on top if you want to create a nice visible border.
Now you are done. You have successfully placed a border between your grass and other landscaping. This will help keep the weeds out and let you avoid mowing up into the flowerbeds. The border will help prevent weeds and provide the needed separation between the beds and the grass.
About the Author:
When you are looking for information about plastic bender board, come to our web pages online today. More details are available at http://www.bestedging.com now.
No comments:
Post a Comment